Leveraging the self-heating effect of ntc thermistor to detect its minimum coverage by a dispensed paste in the mass production process of temperature sensors

Saúl Alejandro Rodríguez Jiménez LEONOR ADRIANA CARDENAS ROBLEDO (2023, [Artículo])

This paper develops a device capable of confirming the minimum coverage area on a thermistor by a thermal paste dispensed and cured in the manufacturing process of Exhaust Gas Recirculation (EGR) temperature sensors to provide the required fixation in the presence of mechanical shock conditions. Such a device leverages the thermistor’s self-heating effect and the thermal conductivity of the paste to read the voltage drop from the sensor, which translates into paste coverage area. The methodology follows a synthesized procedure to develop equipment and processes, considering an early phase for concept confirmation to demonstrate the feasibility of the device development. In a later phase, the optimal parameters are calculated and set to the device for delivering the corresponding classification of the sensors during the test. Once launched in production, the device demonstrates high effectiveness in screening out the sensors with rejectable paste coverage area on the thermistor.

Self-heating effect Thermistor Paste Temperature sensor Heat dissipation INGENIERÍA Y TECNOLOGÍA CIENCIAS TECNOLÓGICAS OTRAS ESPECIALIDADES TECNOLÓGICAS OTRAS OTRAS

Presencia y tratamiento de compuestos disruptores endócrinos en aguas residuales de la Ciudad de México empleando un biorreactor con membranas sumergidas

Occurrence and treatment of endocrine disrupter chemicals in Mexico City waste water semploying submerged membrane bioreactor

Edson Estrada Petia Mijaylova Nacheva GABRIELA ELEONORA MOELLER CHAVEZ GABRIELA MANTILLA MORALES NORMA RAMIREZ SALINAS Manuel Sanchez (2013, [Artículo])

El objetivo de este trabajo fue detectar la presencia de tres compuestos disruptores endócrinos (estrógenos) en aguas residuales de la Ciudad de México y evaluar el desempeño de un biorreactor con membranas sumergidas (BRMS) a nivel planta piloto para remover estrógenos presentes en las aguas residuales de la zona metropolitana. Los compuestos estrona (E1), estradiol (E2) y 17α-etinilestradiol (EE2) fueron detectados en dos diferentes aguas residuales con concentraciones de hasta 90 ng.L–1. El biorreactor fue operado durante 234 días. El biorreactor con membranas fue evaluado con tiempos de residencia hidráulico (TRH) de 7, 9,10 y 12 horas. Con TRH mayores a 7 h y con un tiempo de retención celular (TRC) de 60 d, se obtuvieron remociones de E1, E2 y EE2 superiores a 96% con concentraciones en el efluente del reactor por debajo de 1 ng.L–1. Se detectó la presencia de los estrógenos sobre el lodo activado con concentraciones de hasta 70 ng.g–1. El ensuciamiento de las membranas fue menor con un TRH de 12 horas.

The aim of this work was to detect the presence of three endocrine disruptor compounds (estrogens) in Mexico City’s wastewater and to evaluate the performance of submerged membrane bioreactor (SMBR) pilot plant to remove estrogens present in the wastewater of the metropolitan area. Estrone (E1), estradiol (E2) and 17α-ethinylestradiol (EE2) concentrations ranged up to 90 ng.L–1 were detected in two Mexico City wastewaters. The bioreactor was operated for 234 days. The membrane bioreactor was evaluated at hydraulic residence time (HRT) of 7, 9.10 and 12 hours. At HRT higher than 7 hours and at solid retention time (SRT) of 60 days, the estrogen removals were higher than 96%. At these conditions, the estrogen concentrations in the reactor effluent were lower than 1 ng.L–1. Accumulated concentrations of estrogens were observed in the activated sludge (up to 70 ng.g–1). Membrane fouling was lower at HRT of 12 hours.

Biorreactores Disruptores endócrinos Estrógenos Ciudad de México Tratamiento de aguas residuales INGENIERÍA Y TECNOLOGÍA

Resistencia a afidos en trigo

Leonardo Abdiel Crespo Herrera (2022, [Objeto de congreso])

CIENCIAS AGROPECUARIAS Y BIOTECNOLOGÍA WHEAT PESTS CLIMATE CHANGE APHIDOIDEA DISEASE RESISTANCE

Phenotyping for Disease Resistance to increase genetic gains

Suresh L.M. (2022, [Objeto de congreso])

CIENCIAS AGROPECUARIAS Y BIOTECNOLOGÍA MAIZE PLANT DISEASES DISEASE RESISTANCE PHENOTYPES

Distance learning for farmers: Experience during the pandemic

Andrea Gardeazabal (2023, [Documento de trabajo])

In response to the COVID-19 pandemic's disruption of farmer training—a crucial component for enhancing the resilience and livelihoods of smallholder farmers—CIMMYT innovated educational solutions to sustain capacity building in agri-food systems. Addressing the challenges of limited mobile device access, poor internet connectivity, and digital illiteracy, CIMMYT implemented two pilot projects in Mexico. These projects facilitated distance learning for adult farmers in rural areas, employing both internet-based and non-internet methods. The non-internet approach utilized traditional media like print, while the internet-based approach leveraged WhatsApp for educational content delivery. Building on these experiences, CIMMYT expanded its offerings by creating micro -courses delivered through WhatsApp, hosted on the Co-LAB's new Learning Network platform, specifically targeting farmers. This paper delves into the various strategies, methods, and techniques adopted, documenting the learning outcomes, results, and key conclusions drawn from these innovative training initiatives.

Distance Learning Digital Inclusion Innovative Training CIENCIAS AGROPECUARIAS Y BIOTECNOLOGÍA DISTANCE EDUCATION CAPACITY DEVELOPMENT METHODS COMMUNICATION TECHNOLOGY

Wheat rust early warning systems in Ethiopia: implementation of remote sensing technologies to combat crop disease

Gerald Blasch (2020, [Objeto de congreso])

CIENCIAS AGROPECUARIAS Y BIOTECNOLOGÍA RUSTS MONITORING DISEASE SURVEILLANCE EARLY WARNING SYSTEMS REMOTE SENSING

COVID-19 and family participation in school activities.: Teaching experiences around the Learn at Home program

Evangelina Cervantes Holguín Pavel Roel Gutiérrez Sandoval (2022, [Artículo, Artículo])

The article analyzes, from the qualitative method, the participation of families and teaching staff of the first cycle of primary education in the state of Chihuahua (Mexico) to carry out the various activities of the Learn at Home program implemented in March 2020 as a response to the resulting health confinement by COVID-19. It is concluded that the participation of families in school emergency situations implies improving the relationship between teachers, families, and the community in the implementation processes of educational programs with greater support to organize study times, take advantage of the different cultural capitals and promote family co-responsibility.

Aprendizaje Educación a distancia Enseñanza primaria Epidemia Familia COVID-19 Chihuahua HUMANIDADES Y CIENCIAS DE LA CONDUCTA HUMANIDADES Y CIENCIAS DE LA CONDUCTA Family Elementary education Epidemics Distance education Learning

Las patologías de los recubrimientos en muros y su repercusión en la salud respiratoria de los usuarios

Rosario Tovar (2023, [Tesis de doctorado])

251 páginas. Doctorado en Diseño Bioclimático.

El nivel de calidad del aire interior (CAI) tiene incidencia directa en la salud humana, por eso, es objeto de estudio del diseño bioclimático, toda vez que éste promueve el aprovechamiento de los factores ambientales para la creación y acondicionamiento de espacios en los que los usuarios experimenten confort y bienestar. Además, de impulsar la construcción con sentido común, en donde prevalezca el uso racional de los recursos y una baja dependencia energética. En la presente tesis se pudieron identificar las propiedades de los materiales más comunes que conforman los recubrimientos de muros (cal, cemento, mortero de cemento y yeso) para reconocer los que mejor se adaptan al clima en la Cd. de México, mismos que según se pudo constatar, contribuyen en el control de algunos factores de riesgo (físico: humedad, químico: tóxicos y biológico: microbios) relacionados con una baja calidad del aire al interior de las viviendas. Tal función mitiga o reduce la aparición de algunos de los padecimientos respiratorios más frecuentes en los usuarios como: alergias, asma, rinitis, gripe y sinusitis. Los análisis a los que fueron sometidos los recubrimientos de cuatro materiales ligantes, permitieron evaluar su desempeño ante factores ambientales semi-controlados (temperatura, humedad relativa y concentración de dióxido de carbono) inherentes al funcionamiento del propio espacio interior y al lugar de emplazamiento del mismo. Obviamente, todos los recubrimientos reaccionaron de forma distinta y acorde con las propiedades físicas y químicas de los materiales presentes en cada uno de ellos. Siendo las variaciones más representativas y satisfactorias, las relacionadas con la permeabilidad y el efecto biocida de los recubrimientos hechos con mezcla de cal. Las patologías que mostraron algunos recubrimientos a lo largo del periodo de monitoreo, debido a la insuficiente gestión de la humedad, al alto desarrollo microbiano y a la naturaleza química del material ligante, fueron criptoeflorescencias, moho, bacterias y desprendimiento/diseminación de partículas; mismas que se consideraron definitorias para establecer que al igual que los seres vivos, los materiales de construcción necesitan rangos higrotérmicos específicos, que permitan su óptimo estado de operación. En apego a lo anteriormente citado, es que se considera conveniente concientizar a la población en temas tan importantes para el bienestar social, como la selección de materiales y -consecuente- conservación de los recubrimientos de muros, no sólo para disminuir los costos de ejecución y mantenimiento, sino para aprovechar sus propiedades, ya que tienen una incidencia directa en lo relacionado con el control de las condiciones ambientales básicas, la regulación de la calidad del aire interior y por ende, en la salud de los usuarios. Dicha labor puede iniciar en la etapa formativa de los profesionales de la construcción, con la intención de normalizar el estudio o correcta selección de los sistemas constructivos en función del clima, pero también identificando la función de cada espacio; para garantizar así, que las propuestas de diseño responderán -satisfactoriamente- a los requerimientos de regulación de la humedad, mediante su absorción, transpiración y/o evaporación.

The level of indoor air quality (IAQ) has a direct incidence on the human health, therefore, is the object of study of bioclimatic design, since it promotes the harnessing environmental factors for the creation and conditioning of spaces in which users experience comfort and well-being. In addition, to encourage construction with common sense, where the rational use of resources and low energy dependence prevail. In this thesis it has been identified the properties of the materials that make up the most common wall coverings (hydrated lime, cement, cement mortar and gypsum) for recognizing those that best adapt to the weather in Mexico City, as it could be verified, they contribute to the control of some risk factors (physical:moisture, chemical:toxics and biological:microbes) related with a low indoor air quality at dwellings. This function mitigates or reduces the appearance of some of the most frequent respiratory ailments in users such as: allergies, asthma, rhinitis, flu and sinusitis. The analyses to which the coatings of four binding materials were subjected, allowed to evaluate their performance in the face of semi-controlled environmental factors (temperature, relative humidity, and carbon dioxide concentration) inherent to the operation of the interior space itself and the place of its location. Obviously, all the coatings reacted differently and according with the physical and chemical properties of the materials in each of them. Being the most representative and satisfactory variations, those related to the permeability and biocidal effect of coatings made with hydrated lime mixture. The pathologies that some coatings showed throughout the monitoring period, due to insufficient moisture management, the high microbial development, and the chemical nature of the binding material, were cryptoefflorescences, mold, bacteria and particle shedding/dissemination; they were defining to establish that in similar way to living beings, building materials need specific hygrothermal ranges, to let them works in an optimal state. According with the above, it is considered convenient to raise awareness among the population on issues as important for social welfare, such as the selection of materials and -consequently- conservation of wall coverings, not only to reduce the costs of execution and maintenance, but to take advantage of their properties, since they have a direct incidence in all related with the control of basic environmental conditions, the regulation of indoor air quality and therefore, in users’ health. This work can begin in the formative stage of construction professionals, with the intention of standardizing the study or correct selection of construction systems depending on the weather, but also identifying the function of each space; to guarantee that the design proposals will respond -satisfactorily- to the requirements of humidity regulation, through its absorption, transpiration and/or evaporation.

Muro, recubrimientos, patologías, salud. Wall, coating, pathologies, health. Indoor air pollution--Health aspects. Architecture--Health aspects. Interior walls. Protective coatings. Lime as a disinfectant. Building materials. Communicable diseases--Transmission--Prevention. Contaminación del aire interior. Muros interiores. Revestimientos. Cal como desinfectante. RA577.5 HUMANIDADES Y CIENCIAS DE LA CONDUCTA CIENCIAS DE LAS ARTES Y LAS LETRAS ARQUITECTURA DISEÑO ARQUITECTÓNICO

EFFICIENT FLUORESCENT AND PHOSPHORESCENT OLEDs BY SPIN COATING TECHNIQUE AND A NEW ANODE BASED ON CONDUCTIVE PEDOT:PSS

Luis Abraham Lozano Hernández (2020, [Tesis de doctorado])

"Fluorescent and phosphorescent Organic Light Emitting Diode (OLED) devices were fabricated by solution process and optimized. From their basic characterization (J-V-L curves, electroluminescence spectra) external quantum efficiency (EQE) was calculated. Two small molecule, carbazole derivatives (CZ-1 and CZ-2), previously reported and used for OLEDs showed very good luminances (~ 4000 cd/m2) and current densities (< 200 mA/cm2) resulting in a high EQE (9.5 %). Likewise, fluorescent OLEDs based in the new polymer PF-2F presented an acceptable performance even on a simple architecture with a good EQE (2.6 %), photoluminescence quantum yield (PLQY) about 1 and excellent properties of processability. The influence of its CF3 group in the optical, chemical, electronic and mechanical properties in OLEDs was determined.

Also, a new family of three fluorescent oligomers (BT-F32, BT-F42 and BT-F52) with excellent properties in solution, high PLQY (~1) and highly luminescent, were used in simple and multilayer OLEDs achieving a very high luminance (29 499 cd/m2). These oligomers have different chain lengths, which influence the device luminance, efficiency and their lifetime. Lifetime was monitored and the stretched exponential decay (SED) model was used in order to obtain the device half-life (LT50). Also, phosphorescent devices, based on a host/guest system (PVK:Ir(ppy)3), were prepared, the influence of the electron transport layer (ETL) into the electron/hole ratio was analyzed.

By using a new proposed method, a PEDOT:PSS anode was developed and applied in rigid and flexible substrates, with low sheet resistance (40 Ω/□) and acceptable transmittance (> 85%). This new proposed method consists in volume evaporation, in which basically the loss of water induces closeness among the conductive fractions of PEDOT. This PEDOT:PSS anode easy of fabricating following an economical procedure could be applied not just in OLEDs but in other optoelectronic devices such as organic photovoltaic cells (OPVs), perovskite solar cells (PeSCs), etc."

OLEDs Fluorescence Phosphorescence PEDOT:PSS Polymer Anode INGENIERÍA Y TECNOLOGÍA CIENCIAS TECNOLÓGICAS TECNOLOGÍA ELECTRÓNICA DISPOSITIVOS SEMICONDUCTORES DISPOSITIVOS SEMICONDUCTORES

Directrices mínimas dentro del ecosistema del Internet de las Cosas y su implementación en México

Miguel Ángel Acosta García (2023, [Otro, Trabajo de grado, maestría])

Durante los últimos años el crecimiento del Internet de las Cosas ha sido exponencial ya que presta servicios mediante la interconexión de objetos físicos o virtuales. Lo anterior con apoyo de la interoperabilidad de las tecnologías de la comunicación y de la infraestructura transfronteriza en beneficio de la sociedad de la información. En ese sentido el Estado mexicano requiere analizar la viabiliad de establecer la posible regulación del IoT para aumentar la competitividad

económica en el mercado y el bienestar de los ciudadanos, pero con una visión regulatoria integral con la participación

de diversos sectores para el desarrollo del ecosistema del IoT.

Internet de las Cosas Ecosistema del Internet Dispositivos IoT INGENIERÍA Y TECNOLOGÍA INGENIERÍA Y TECNOLOGÍA